Now You Lot Know Repair Difficult Crusade Bad Sector 6

Repair Hard Drive Bad Sector, Case No. 5

Turn on computer, press Delete/Esc/F2 to function inward BIOS
SATA Controller Mode. SATA Controller Mode from AHCI, changed to IDE / Compatibility

Damage Analysis No. 1. Checking partition. How; Press START - Programs - Administrative Tools - Disk Management. Open the Disk Management to banking enterprise check the system partition. When the drive had bad sectors, mayhap corrupted system partition. Information from Disk Management is very important, because nosotros can find out where the bad sectors, and its effect on the drive, so that we can make a decision before the repair begins.

Information from Disk Management, follow up by checking; location and the position out of bad sectors. Inspection is done by HDD Regenerator. HDD Regenerator can hold upwardly institute in Hiren's BootCD 9.9

Damage Analysis No.2. Checking bad sectors. Restart the computer - Start BootCD - Hard Disk Tools - HDD Regenerator - Enter - Scan, but do not repair (show bad sectors). Information about the place of bad sectors, and the position out of bad sectors is very important.

When the scan, simply practise non repair (show bad sectors), the obtained results every bit shown below, follow the adjacent steps

Step 3. Improvement

Insert Hiren's BootCD - Restart the computer - Start BootCD - Hard Disk Tools - HDD Regenerator - Enter - Scan as well as repair (1)
Scan and repair must hold upwardly done to complete, should non hold upwardly forced to stop, should non be interrupted.
Scan and repair, must hold upwardly 100% complete, although it takes a long time
After the scan and repair is completed, the adjacent measuring is to save the data.

If the scan and repair, sudden stops, and the message as shown below, turn off the computer or laptop, rest hard drive about an hour (to lower the temperature of the drive), as well as and therefore repeat the scan and repair.

Special conditions. 1. If the scan and repair running very slow, 2. If the scan and repair takes a very long time (over iv hours), 3. If the scan and repair always stop suddenly, mean, bad sectors in the drive so badly. In this condition, at that spot volition hold upwardly a drive failure, or will happen SMART Failure Predicted on Hard Drive. In this condition, the drive is not feasible to use. In this condition, repairs done inward order to save the data. Saving data, with very severe bad condition, is a really hard job. If you have problem doing it myself, I recommend, leave this job to the professionals

Note; so that data can be saved, scan and repair bad sectors, should hold upwardly 100% complete.

Step 4. Data Rescue

Rescue Data. After the scan and repair with HDD Regenerator is complete, turn off the computer / laptop. Remove the hard drive and connect it to some other computer.

Preparation; 1. Turn off covert saver, 2. Power schemes, Turn off monitor = never, plough of HD = never, 3. Disable/delete all Scheduled Task, 4. Disconnect internet, 5. Free infinite to salve the data, 6. Do non opened upwardly whatever other applications during information recovery process, 7. Don't opened upwardly drive bad. Example; drive master copy (normal disk) = C,D as well as east (CD Room). Drive bad F,G,H. Bad located on drive F as well as G. Don't opened upwardly drive F/G, from windows explorer or my computer, because tin convey novel bad sectors (new bad sectors appear).
Bad sector place on drive F/G. To rescue information on drive F/G, done amongst recovery software. Example; EASEUS Data Recovery, Get Data Back, etc.

Drive H normal or no bad found. To rescue the data, tin hold upwardly done past times re-create as well as paste.

Rescue information on drive bad, I recommended don't practise past times re-create as well as paste, because tin convey novel bad sectors (new bad sectors appear).

If rescue information on drive bad is fail, QUICK FORMAT drive bad (DON'T FULL FORMAT), as well as repeat recovery process. If file organisation drive bad is NTFS - quick format NTFS, if FAT32 - quick format FAT32.

If recovery information on drive bad notwithstanding fail, repeat the scan as well as repair procedure amongst HDD Regenerator. Example; bad on drive F (100 GB). Scan as well as repair from 0 - 100 GB. After procedure is finish, residue disk few hours, as well as therefore repeat recovery procedure amongst GET Data Back. How to recover; recover is done inward several stages, for example; recovery of 0 - thirty GB, 29 GB - l GB, 49 GB - seventy GB, 69 GB - 100 GB. This method is done when, recovering from 0-100 GB e'er failed, as well as therefore recovered done inward several stages.

So, how to recover information from drives bad, Step 1. Scan as well as repair bad sectors. Step 2. To drive at that spot are bad found, done amongst recovery software. To drive that is no bad found, done past times re-create as well as paste.

Step 6. Feasibility Study

For this case, scan as well as repair or Low Level Format, can't repair this case. For this case, although the disk successfully repaired, the harm volition most probable occur again. After the information has been saved, you lot should usage a novel disk instead.
The master copy purpose repair disk to save the data.
If the number of bad on the disk too much, and bad layout spread across drives, then the best solution is to supersede the hard drive.

Data tin hold upwardly saved, the disk is non viable to usage because, bad sectors spread throughout the disk

Data tin hold upwardly saved, the disk tin notwithstanding hold upwardly used because, bad sectors doesn't spread throughout the disk