Now You Lot Know Repair Difficult Displace Bad Sector 5
Repair Hard Drive Bad Sector, Case No. 4
Step 1. Preparation Before Repair
- Download Hiren's Boot CD 9.9 (iso file)
- Download BurnCDCC
- Make bootable CD, Hiren's Boot CD 9.9
- You can use the Hiren's BootCD, higher version
Step 2. Damage Analysis
- Turn on computer, press Delete/Esc/F2 to piece of work inward BIOS
- SATA Controller Mode. SATA Controller Mode from AHCI, changed to IDE / Compatibility
- Setting the boot. First boot is CD Room
- Insert Hiren's CD, save the BIOS settings and restart
- When Hiren's Boot CD menu appears, select Start Mini Windows XP - Enter.
- Damage Analysis No. 1. Checking partition. How; Press START - Programs - Administrative Tools - Disk Management. Open the Disk Management to banking concern gibe the system partition. When the drive had bad sectors, perchance corrupted system partition. Information from Disk Management is very important, because nosotros can find out where the bad sectors, and its effect on the drive, so that we can make a decision before the repair begins.
- Information from Disk Management, follow up by checking; location and the expose of bad sectors. Inspection is done by HDD Regenerator. HDD Regenerator can last constitute in Hiren's BootCD 9.9
- Damage Analysis No.2. Checking bad sectors. Restart the computer - Start BootCD - Hard Disk Tools - HDD Regenerator - Enter - Scan, but do not repair (show bad sectors). Information about the place of bad sectors, and the expose of bad sectors is very important.
- When the scan, but do not repair (show bad sectors), the obtained results as shown below, follow the adjacent steps
Step 3. Initial Improvement
- Insert Hiren's BootCD - Restart the computer - Start BootCD - Hard Disk Tools - HDD Regenerator - Enter - Scan together with repair (1)
- Scan together with repair must last done to complete, should non last forced to stop, should non last interrupted.
- Scan together with repair, must last 100% complete, although it takes a long time
- After the scan together with repair is completed, the adjacent measuring is to salve the data.
- If the scan and repair, sudden stops, and show message "Hard drive is non ready", turn off the computer or laptop, rest hard drive about an hour (to lower the temperature of the drive), together with thus repeat the scan and repair.
- if the scan together with repair, precipitous stops, together with demo message "Hard drive is non ready", plough off PC/Laptop. Remove hard drive. Connect amongst some other PC/Laptop, through USB connect. Open HDD Regenerator from PC/Laptop, scan together with repair, hard drive bad
- Special conditions. 1. If the scan and repair running very slow, 2. If the scan and repair takes a very long time (over iv hours), 3. If the scan and repair always stop suddenly, mean, bad sectors in the drive so badly. In this condition, at that spot volition last a drive failure, or will happen SMART Failure Predicted on Hard Drive. In this condition, the drive is not feasible to use. In this condition, repairs done inward order to save the data. Saving data, with very severe bad condition, is a real hard job. If you have problem do it, I recommend, leave this job to the professionals
- Note; so that data can be saved, scan and repair bad sectors, should last 100% complete.
- Rescue Data. After the scan and repair with HDD Regenerator is complete, turn off the computer / laptop. Remove the hard drive and then connect it to some other computer.
- Preparation; 1. Turn off shroud saver, 2. Power schemes, Turn off monitor = never, plough of hard disk drive = never, 3. Disable/delete all Scheduled Task, 4. Disconnect internet, 5. Free infinite to salve the data, 6. Do non opened upward any other applications during data recovery process, 7. Don't opened upward drive bad. Example; drive primary (normal disk) = C,D together with eastward (CD Room). Drive bad F,G,H. Bad located on drive F. Don't opened upward drive F, from windows explorer or my computer, because can bring new bad sectors (new bad sectors appear).
- Bad sector place on drive C. To rescue information on drive C, done amongst recovery software. Example; EASEUS Data Recovery, Get Data Back, etc.
- Drive D/E normal or no bad found. To rescue the data, tin lav last done by copy and paste.
- Rescue information on drive bad, I recommended don't practise past times re-create together with paste, because can bring new bad sectors (new bad sectors appear).
- If rescue information on drive bad is fail, QUICK FORMAT drive bad (DON'T FULL FORMAT), together with repeat recovery process. If file arrangement drive bad is NTFS - quick format NTFS, if FAT32 - quick format FAT32.
- If recovery information on drive bad notwithstanding fail, repeat the scan and repair process with HDD Regenerator. Example; bad on drive C (100 GB). Scan together with repair from 0 - 100 GB. After procedure is finish, residue disk few hours, thus repeat recovery procedure amongst GET Data Back. How to recover; recover is done in several stages, for example; recovery of 0 - 30 GB, 29 GB - 50 GB, 49 GB - 70 GB, 69 GB - 100 GB. This method is done when, recovering from 0-100 GB always failed, then recovered done in several stages.
- So, how to recover data from drives bad, Step 1. Scan and repair bad sectors. Step 2. To drive there are bad found, done with recovery software. To drive that is no bad found, done by copy and paste.
Step 5. Maximum Improvement
After the data has been saved, there are two solutions;- Replacing the hard drive with a novel one (Recommended)
- Make improvements, then the feasibility study, and then install the operating system and restore data.
For you who are interested inward doing repair hard drive. Continue reading (under construct)