Now Y'all Know Repair Difficult Travail Bad Sector 7

Repair Hard Drive Bad Sector, Case No. 6

Turn on computer, press Delete/Esc/F2 to run inwards BIOS
SATA Controller Mode. SATA Controller Mode from AHCI, changed to IDE / Compatibility

Damage Analysis No. 1. Checking partition. How; Press START - Programs - Administrative Tools - Disk Management. Open the Disk Management to banking concern check the system partition. When the drive had bad sectors, mayhap corrupted system partition. Information from Disk Management is very important, because nosotros can find out where the bad sectors, and its effect on the drive, so that we can make a decision before the repair begins.

Information from Disk Management, follow up by checking; location and the discover of bad sectors. Inspection is done by HDD Regenerator. HDD Regenerator can endure constitute in Hiren's BootCD 9.9

Damage Analysis No.2. Checking bad sectors. Restart the computer - Start BootCD - Hard Disk Tools - HDD Regenerator - Enter - Scan, but do not repair (show bad sectors). Information about the place of bad sectors, and the discover of bad sectors is very important.

When the scan, but do not repair (show bad sectors), the obtained results as shown below, follow the side past times side steps

Step 3. Initial Improvement

Insert Hiren's BootCD - Restart the computer - Start BootCD - Hard Disk Tools - HDD Regenerator - Enter - Scan too repair (1)
Scan too repair must endure done to complete, should non endure forced to stop, should non endure interrupted.
Scan too repair, must endure 100% complete, although it takes a long time
After the scan too repair is completed, the side past times side mensuration is to salve the data.

If the scan and repair, sudden stops, and the message as shown below, turn off the computer or laptop, rest hard drive about an hour (to lower the temperature of the drive), too and thus repeat the scan and repair.

Special conditions. 1. If the scan and repair running very slow, 2. If the scan and repair takes a very long time (over iv hours), 3. If the scan and repair always stop suddenly, mean, bad sectors in the drive so badly. In this condition, at that topographic point volition endure a drive failure, or will happen SMART Failure Predicted on Hard Drive. In this condition, the drive is not feasible to use. In this condition, repairs done inwards order to save the data. Saving data, with very severe bad condition, is a real hard job. If you have problem do it, I recommend, leave this job to the professionals

Note; so that data can be saved, scan and repair bad sectors, should endure 100% complete.

Step 4. Data Rescue

Preparation; 1. Turn off covert saver, 2. Power schemes, Turn off monitor = never, plow of HD = never, 3. Disable/delete all Scheduled Task, 4. Disconnect internet, 5. Free infinite to salve the data, 6. Do non opened upward whatever other applications during information recovery process, 7. Don't opened upward drive bad. Example; drive original (normal disk) = C,D too due east (CD Room). Drive bad F,G,H. Bad located on drive F/G/H. Don't opened upward drive F/G/H, from windows explorer or my computer, because tin choose novel bad sectors (new bad sectors appear).

Bad sector place on drive F/G/H. To rescue information done amongst recovery software. Example; EASEUS Data Recovery, Get Data Back, etc.

Rescue information on drive bad, I recommended don't exercise past times re-create too paste, because tin choose novel bad sectors (new bad sectors appear).

If rescue information on drive bad is fail, QUICK FORMAT drive bad (DON'T FULL FORMAT), too repeat recovery process. If file organization drive bad is NTFS - quick format NTFS, if FAT32 - quick format FAT32.

If recovery information on drive bad notwithstanding fail, repeat the scan too repair procedure amongst HDD Regenerator. Example; bad on drive F (100 GB). Scan too repair from 0 - 100 GB. After procedure is finish, residuum disk few hours, too thus repeat recovery procedure amongst GET Data Back. How to recover; recover is done inwards several stages, for example; recovery of 0 - thirty GB, 29 GB - l GB, 49 GB - seventy GB, 69 GB - 100 GB. This method is done when, recovering from 0-100 GB e'er failed, too thus recovered done inwards several stages
To rescue the data drive F, G, H can endure done with recovery software. Example; EASEUS Data Recovery, Get Data Back, etc.

So, how to recover data from drives is bad, Step 1. Scan and repair bad sectors. Step 2. Rescue information amongst the recovery software. Example; EASEUS Data Recovery, GetDataBack, etc..

Step 6. Feasibility Study

Scan too repair or Low Level Format, can't repair this case. For this case, although the disk successfully repaired, the harm volition most probable occur again. After the information has been saved, y'all should utilization a novel disk instead.
The principal role repair disk to salve the data.
If the discover of bad on the disk besides much, too bad layout spread across drives, too thus the best solution is to supervene upon the hard drive.

Data tin endure saved, the disk is non viable to utilization because, bad sectors spread throughout the disk

Data tin endure saved, the disk tin notwithstanding endure used because, bad sectors doesn't spread throughout the disk